SUB-BASS TEST TONE

20 Hz Sub-Bass Tone Generator

Generate a pure 20 Hz sine wave tone in your browser. 20 Hz sits at the extreme lower limit of human hearing, making it the ideal reference signal for testing subwoofers, deep bass drivers, and structural vibrations.

AUDIO FREQUENCY
20 Hz
Ready
WaveformSmooth and pure
sine
20 Hz – 20 kHz
Hz
20 Hz1 kHz10 kHz20 kHz
Quick frequenciesλ ∝ 1 / f
Frequency20 Hz
×
Visual wavelength3.96k px
22.00× longer wavelength than 440 Hz

Start audio only when you press play. Keep your device volume low before testing.

15%
Frequency20 Hz20 cycles per second
Audio BandSub-BassAcoustic spectrum category
Wavelength in Air17.15 meters (56.3 ft) at 20°Cλ = v / f (at 20°C)
Perception Profile: Extreme lower threshold of human hearing; perceived primarily through tactile vibration and bone conduction rather than audible pitch.

PHYSICAL ACOUSTICS

Acoustic Physics of 20 Hz

A 20 Hz acoustic wave oscillates exactly 20 times per second. In standard atmospheric conditions (air at 20°C / 68°F), sound travels at approximately 343 meters per second. This results in an enormous wavelength of 17.15 meters (over 56 feet). Because this physical wave is larger than almost any domestic listening room, a 20 Hz tone operates inside rooms primarily via room pressurization rather than standard free-field wave propagation.

To the human ear, 20 Hz is located right at the absolute lowest threshold of audible perception. According to the Fletcher-Munson equal-loudness contours (ISO 226), the human auditory system is exceptionally insensitive to ultra-low frequencies. A 20 Hz tone requires sound pressure levels of 70 to 80 dB SPL merely to become faintly perceptible to a healthy human ear. Rather than hearing a clear musical pitch, listeners usually perceive 20 Hz as a low, throbbing flutter accompanied by chest pressure or floor vibrations.

PRACTICAL TESTING

Subwoofer & Speaker Testing at 20 Hz

01

Subwoofer Extension & F3 Cutoff Verification

Most compact desktop speakers and small bookshelf monitors cannot reproduce 20 Hz; their crossover or high-pass filter cuts off well above this range. Playing 20 Hz tests whether your dedicated subwoofer truly extends down to the 20 Hz mark without heavy roll-off.

02

Port Turbulence & Air Chuffing Detection

Bass reflex (ported) enclosures experience maximum port air velocity near their tuning frequency. If the port design is restrictive or un-flared, 20 Hz playback will produce audible wind noise ('chuffing') or whistling around the port opening.

03

Cone Excursion & Mechanical Clearance Check

Because air displacement requirements quadruple for every halving of frequency (displacement ∝ 1/f²), reproducing 20 Hz requires massive driver cone excursion. Observe the woofer cone at moderate volume: it should oscillate smoothly without bottoming out against the backplate or voice-coil rubbing.

04

Room Boundary & Infrasonic Resonances

Ultra-low bass excites room boundaries, doors, loose windows, and drywall. Playing a steady 20 Hz tone allows you to walk through the listening space and pinpoint rattles, loose fixtures, and acoustic buzzes that degrade audio clarity.

TROUBLESHOOTING & DIAGNOSTICS

What to Listen For at 20 Hz

When evaluating speakers, headphones, or audio rooms, listen closely for these common acoustic and mechanical anomalies:

Audible buzzing or fluttering from speaker enclosure

Probable cause: Air leaks around driver gaskets, amplifier mounting plates, or loose screws vibrating under intense internal acoustic pressure.

Complete silence despite high volume setting

Probable cause: The playback device (e.g. laptop speakers, phone, budget headphones) has an active high-pass filter or physical cone roll-off cutting off frequencies below 50–80 Hz.

Clicking or harsh knocking sound

Probable cause: The subwoofer driver is exceeding its maximum linear mechanical excursion (Xmax) and bottoming out. Reduce system volume immediately to prevent permanent driver damage.

SAFETY & EQUIPMENT PROTECTION

Crucial Equipment Safety at 20 Hz

Never turn up your amplifier to high volume simply because you cannot hear the 20 Hz tone! Because the human ear is relatively insensitive to 20 Hz, users are often tempted to crank the volume control. However, the amplifier is delivering massive electrical power and the woofer is moving with maximum excursion. Excessive volume can quickly burn out voice coils or mechanically damage speaker suspensions without ever sounding loud to human ears. Always start at near-zero volume and increase gradually.

FAQ

20 Hz Frequently Asked Questions

Why can't I hear anything when playing a 20 Hz tone on my phone or laptop?

Smartphones, laptops, and compact computer speakers have miniature drivers (typically 1 to 2 inches in diameter) that physically cannot move enough air to produce a 17-meter sound wave. Built-in DSP chips also apply steep high-pass filters below 80–100 Hz to prevent tiny drivers from distorting. You need a dedicated subwoofer or high-quality over-ear headphones to hear and feel 20 Hz.

Can 20 Hz damage my subwoofer or headphones?

Yes, if played at high volume. Because 20 Hz requires large mechanical displacement, driving a speaker hard at 20 Hz can cause the voice coil to hit the magnet backplate or overheat. Keep playback volume moderate.

What is the difference between 20 Hz and infrasound?

Infrasound is defined as sound below 20 Hz (e.g., 1 Hz to 19 Hz), which is considered below the standard nominal threshold of human hearing. 20 Hz is the accepted boundary line: it is the lowest nominal limit of human audio perception.

Why does 20 Hz sound like a flutter instead of a smooth note?

At 20 oscillations per second, the human ear and brain can almost perceive individual pressure cycles rather than integrating them into a continuous pitch sensation. This creates a distinctive fluttering or pulsating sensation.

FREQUENCY SPECTRUM

Compare Other Audio Frequencies

Switch seamlessly from 20 Hz to other key benchmark frequencies to test different portions of your speaker and headphone response.