LOUDSPEAKER DIAGNOSTICS
Speaker Test Tone
Test your loudspeakers, studio monitors, soundbars, and subwoofers with precise browser-generated test tones. Diagnose driver health, room resonance, crossover smoothness, and stereo imaging.
Start audio only when you press play. Keep your device volume low before testing.
DIAGNOSTIC PROTOCOL
Comprehensive 5-Step Speaker Check
Initial Baseline Audio Verification (440 Hz / 1 kHz)
Start by playing a mid-frequency tone (440 Hz or 1 kHz) at low volume. Confirm that both left and right speakers produce sound clearly without crackling, distortion, or intermittent signal drops.
Subwoofer & Low-Frequency Extension (20 Hz – 80 Hz)
Switch to 40 Hz or 60 Hz. Listen for smooth, deep bass reproduction. Watch the woofer cone move and listen near the bass reflex port for wind noise, air chuffing, or whistling.
Woofer Crossover & Cabinet Resonance (80 Hz – 250 Hz)
Play tones between 90 Hz and 180 Hz while placing your fingertips lightly on the side panels of the speaker cabinet. Quality cabinets remain stiff and inert; vibrating walls indicate poor internal bracing that adds boxy coloration to music.
Midrange Clarity & Vocal Band (500 Hz – 3 kHz)
Check whether the tone sounds pure and centered. This range handles the fundamental frequencies of human speech. Any fuzziness or buzzing here points to voice coil rubbing or cone fatigue.
Tweeter Output & Dispersion (5 kHz – 12 kHz)
Verify that your tweeters are operating. High frequencies are directional; step 30 degrees to the side of the speaker to test off-axis dispersion. A sudden volume cliff indicates narrow beaming.
TROUBLESHOOTING
Identifying Common Speaker Faults
Weak Bass & Thin Sound
Cause: Phase cancellation. If the speaker wires are connected (+ to -) on one speaker and (+ to +) on the other, the two speakers work in opposition, canceling bass waves in the room. Swap the positive and negative terminals on one speaker to fix.
Rattling at Specific Frequencies
Cause: Sympathetic mechanical resonance. A specific frequency (e.g. 110 Hz) excites the natural resonance of a loose screw, speaker grille clip, or nearby picture frame. Pinpoint by listening closely while the tone plays.
Raspy or Scratchy Sound
Cause: Voice coil rub. When a speaker is overheated or dropped, the voice coil former can warp and scrape against the permanent magnet assembly. Gently press the cone in and out with four fingers (while powered off); if it scrapes, the driver requires replacement.
No High-Frequency Tone
Cause: Blown tweeter or faulty crossover capacitor. If tones at 6 kHz or 10 kHz are completely silent while low tones play fine, the tweeter dome or crossover high-pass filter has failed.
FREQUENCY SPECTRUM
Test Specific Frequencies on Your Speakers
Select individual frequencies to test specific speaker components: subwoofers (20 Hz), woofers (100 Hz), reference midrange (440 Hz & 1 kHz), or tweeters (5 kHz & 10 kHz).
FAQ
Frequently Asked Questions about Speaker Testing
What is the best frequency to test if my speakers are working?
A 440 Hz or 1 kHz sine wave is ideal for an initial check. Both frequencies sit comfortably within the middle of the human hearing range and are easily reproduced by virtually every loudspeaker, soundbar, and desktop monitor without stressing woofers or tweeters.
How do I test my subwoofer vs my main speakers?
Play frequencies below 80 Hz (such as 30 Hz to 60 Hz) to test your subwoofer. At these low frequencies, main satellite speakers roll off, and the subwoofer should take over. For woofers in bookshelf or floorstanding speakers, test between 100 Hz and 500 Hz. For tweeters, test frequencies above 3 kHz to 10 kHz.
Why do my speakers rattle or buzz during bass tests?
Rattling usually stems from one of three sources: (1) loose speaker grilles, screws, or enclosure joints vibrating under internal acoustic pressure; (2) objects near the speaker (such as picture frames, desk surfaces, or shelves) resonating sympathetically; or (3) physical driver voice-coil rubbing against the magnet gap due to age or mechanical overload.
What does 'speaker phase' mean and how do I test it?
Speaker phase refers to whether both left and right speaker cones move outward and inward in unison. If one speaker's positive and negative wires are accidentally reversed, the cones move in opposite directions, canceling out bass frequencies and causing the audio to sound hollow and diffused rather than focused in the center.
Can continuous test tones damage my speakers?
Yes, if played at excessively high volume. In regular music, sound is dynamic with brief transient peaks. A continuous sine tone delivers constant electrical power to the voice coil without pause. Keep volume at moderate conversational levels when testing.
How do I find room acoustic standing waves with a speaker test tone?
Play a steady 80 Hz or 100 Hz sine wave and walk slowly across your listening room. You will notice distinct physical zones where the sound becomes intensely loud (pressure peaks) and zones where it nearly vanishes (phase cancellation nulls). This helps guide ideal listener seating and acoustic panel placement.