MID-BASS / UPPER BASS TEST TONE

100 Hz Bass Tone Generator

Generate a clean 100 Hz pure sine wave tone in your browser. 100 Hz is the foundational mid-bass frequency where subwoofers hand off to main woofers, making it indispensable for crossover tuning and room resonance analysis.

AUDIO FREQUENCY
100 Hz
Ready
WaveformSmooth and pure
sine
20 Hz – 20 kHz
Hz
20 Hz1 kHz10 kHz20 kHz
Quick frequenciesλ ∝ 1 / f
Frequency100 Hz
×
Visual wavelength792.0 px
4.40× longer wavelength than 440 Hz

Start audio only when you press play. Keep your device volume low before testing.

15%
Frequency100 Hz100 cycles per second
Audio BandMid-Bass / Upper BassAcoustic spectrum category
Wavelength in Air3.43 meters (11.25 ft) at 20°Cλ = v / f (at 20°C)
Perception Profile: Easily audible as a warm, authoritative bass hum. This region provides punch, warmth, and body in musical kick drums and basslines.

PHYSICAL ACOUSTICS

Acoustic Significance of 100 Hz

A 100 Hz tone represents 100 sound wave cycles per second with an acoustic wavelength of approximately 3.43 meters (11.25 feet) in air. Unlike extreme sub-bass, 100 Hz sits squarely within the range that nearly all hi-fi speakers, studio monitors, bookshelf speakers, and quality headphones can reproduce effortlessly.

In modern audio production, 100 Hz represents the critical transition zone between the deep sub-bass and the lower midrange. It corresponds closely to the fundamental frequency of the musical note G2 (approximately 98 Hz). This is where kick drums deliver their chest 'thump', electric bass guitars deliver authoritative body, and male vocals derive low-end fullness. It is also the most common frequency region where domestic rooms exhibit severe standing wave peaks and nulls.

PRACTICAL TESTING

Speaker & Subwoofer Testing at 100 Hz

01

Subwoofer-to-Satellite Crossover Integration

Most home theater receivers and studio subwoofer setups set their crossover filter between 80 Hz and 100 Hz. Playing 100 Hz allows you to verify that both the subwoofer and main satellite speakers hand off smoothly without creating a phase cancellation dip or an exaggerated boomy peak.

02

Room Mode (Standing Wave) Mapping

Because a 3.43-meter wavelength matches common room dimensions, 100 Hz strongly excites room modes. Play a steady 100 Hz tone and walk around your room. You will notice spots where the tone sounds extremely loud (peaks) and spots where it almost disappears (nulls). This helps guide ideal listener seating and speaker placement.

03

Speaker Cabinet Rigidity & Panel Resonance

Inexpensive speaker enclosures often suffer from poorly braced MDF or plastic walls that resonate around 90–120 Hz. When playing 100 Hz, place your hand lightly on the speaker cabinet sides. Excessive vibration indicates cabinet coloration that muddies low-end playback.

04

Left/Right Bass Balance in Headphones

Headphone drivers must produce equal bass energy to maintain a coherent soundstage. Playing 100 Hz in headphones should sound centered directly between your ears without drifting toward the left or right earcup.

TROUBLESHOOTING & DIAGNOSTICS

What to Listen For at 100 Hz

When evaluating speakers, headphones, or audio rooms, listen closely for these common acoustic and mechanical anomalies:

The 100 Hz tone suddenly disappears at the listening chair

Probable cause: A room acoustic boundary null (destructive interference where reflected waves cancel direct sound). Adjust speaker toe-in or move seating position 1–2 feet forward or back.

Buzzing from nearby furniture or desk surface

Probable cause: Sympathetic resonance: mechanical vibrations from the speaker are coupling into the desk. Use isolation pads or decoupling foam beneath monitor speakers.

Distorted, rasping sound rather than a smooth round hum

Probable cause: Harmonic distortion in the amplifier or voice coil rubbing in the woofer basket. Lower input gain to confirm whether the issue is electronic clipping or mechanical.

SAFETY & EQUIPMENT PROTECTION

Listening Comfort & Volume Practices

100 Hz is perceived with substantially higher sensitivity than 20 Hz, but prolonged exposure to loud continuous tones can still cause ear fatigue. Set your volume to a normal conversational level before starting playback. When checking for room modes, a moderate volume is completely sufficient.

FAQ

100 Hz Frequently Asked Questions

Why does a 100 Hz tone sound much louder in the corners of my room?

Room corners act as acoustic horn-loading boundaries where room modes converge. Sound pressure accumulates in three-way wall-floor intersections, creating significant bass reinforcement (often +6 to +12 dB higher than the room center).

Should a 100 Hz tone be played through my subwoofer or main speakers?

If your audio system utilizes an 80 Hz crossover, 100 Hz will be reproduced primarily by your main speakers. If your crossover is set to 120 Hz, it will be reproduced by your subwoofer. Testing at 100 Hz helps ensure both sets of drivers blend seamlessly.

What musical note is closest to 100 Hz?

100 Hz is very close to G2 (which is 97.99 Hz in standard A440 concert tuning), about one octave and a half below middle C (C4).

Can 100 Hz help check headphone seal?

Yes. If an over-ear headphone or in-ear monitor does not have an airtight acoustic seal against your head or ear canal, 100 Hz and lower frequencies will lose intensity, resulting in thin, lifeless sound.

FREQUENCY SPECTRUM

Compare Other Audio Frequencies

Switch seamlessly from 100 Hz to other key benchmark frequencies to test different portions of your speaker and headphone response.